• F - 4u Corsair (50cc) Specification: Length: 1735mm(68.3") Wing span: 2160mm(85") Wing area: 87.00sq.dm(9.39sq.ft) Wing loading: 135.6g/sq.dm(44.5oz/sq.ft) Flying weight: 11.8kg(26.0lbs) INSTRUCTION MANUAL Radio: 6ch & 10servos Engine: 50cc gasoline engine This R/C airplane is not a toy! (The people under 18 years old is forbidden from flying this model) First-time builders should seek advice from people having building experience.If misused or abused,it can cause serious bodily injury. • Gasoline tube Gasoline 6 channel radio for aiplane is highly recommended for this model. 50cc gas engine Optional parts: rubber wheel with metal hub. Flash drive for mac install. Spinner nut 22″X8-10 We strongly recommen you use the thread lock for all the screws when you build your model. • Assemble the aileron to main wing with instant type Two wheel retract system Accessory list for the coming installation steps. Make sure to assemble retracts as instructed below. It allows users to play and view most videos, music, podcasts, and other digital media files from local and network storage media and the internet. Kodi app download. Note: To install Kodi on OS X 10.9 Mavericks or later, you need to right-click the application after it has been What's New in Kodi. Kodi (was XBMC) is an award-winning free and open-source (GPL) software media player and entertainment hub that can be installed on Linux, OS X, Windows, iOS, and Android, featuring a for use with televisions and remote controls. Aberdeen has enjoyed a strong relationship as a Supermicro reseller for over 15 years. We gladly offer these low-cost factory direct barebone models to allow our customers to take advantage of our strong relationship with Supermicro. Clevis Clevis Collar (3mm) Rod (2x300mm) TP Screw (2.3x12mm) Servo tray(68.5x56.5x2mm) Ball joint Strut Wooden Block(20x20x8mm) • Secure the servo,assemble the servo to the relevant Adjustment. Drill holes in the flap and epoxy the pin hinges in them. Position in the outer wing. TP Screw (2.3x12mm) Pin hinge(4.5x67mm) 1.5mm Side View AILERON 30mm Rod (2x300mm) 30mm FLAP Nut (3mm ) Screw (3x10mm) • Assemble the wheel mount to the thick wooden block According to the rib template drill holes and trim a slot in Drag one side of the fiberboard out from the slot in the center wing root until the length of the outer Install the wheel to the fixed landing gear. • According to the illustration,epoxy one side of the Trim the dummy engine cover and the canopy fiberboard in one flap and connect another flap Install the servo of flap to the servo tray. Assemble the cowl to the fuselage with TP screws. Carefully along the shaded line. ![]() • Install the servo of switch in the fuselage. Install the switch and the throttle servo Epoxy the flaps to the center wing. Assemble the gear doors and the wheels to the retracts. Set screw (3x4mm) LockNut(4mm) Securely glue together. If coming off during flights, you 'll Bushing (8X4mm) lose control of your airplane which leads to accidents! Washer (2mm) • Trim the surplus section from the wheel door and make sure the retract system can retract into the wings Assemble the engine. Drill two holes to relevant position in the fuselage The front view of the engine install completion. Accurately when the gear up. Wooden Block (2mm Ply) 120 mm 32mm. • The sketch map of the servo wires pass through the Set the U-style wire through the tail of fuselage as Assemble the stabilizer to fuselage and trim slot to Drill holes to relevant position in the tailing edge of frame in the fuselage.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |